5052 Aluminium Sheet
Aluminum alloy 5052 is a non-heat-treatable alloy known for its excellent corrosion resistance, particularly in marine environments. It has good workability and is commonly used in applications that require moderate strength.
| Mechanical Properties: |
|---|
|
Tensile Strength:33,000 psi (228 MPa) Yield Strength:28,000 psi (193 MPa) Elongation:12% |
| Physical Properties: |
|
Density: 2.68 g/cm³ (0.0975 lb/in³) Melting Range: 607°C-650°C (1125°F-1202°F) |
| Typical Uses: |
| Marine applications (boat hulls, shipbuilding) Architecture and construction Automotive components Cooking utensils Electrical appliances General sheet metal work |
| Welding: |
| Alloy 5052 is readily weldable using standard methods such as gas, electric, resistance, and spot welding. |
| Corrosion Resistance: |
| 5052 has excellent corrosion resistance, particularly in marine environments. It is also resistant to saltwater, making it a common choice for applications in coastal regions. |
| Considerations |
| Alloy 5052 is known for its good formability, high fatigue strength, and above-average machinability. It is often used in situations where anodizing or other coatings are applied. |
5052 Aluminium Sheets
Alloy : 1100 1050 1060 1070 1200 2011 2014 2017 2024 3003 3004 3005 3015 3105 5052 5083 5086 5154 5254 5356 5454 5056 5182 5754 6060 6061 6063 6082 6101 7020 7050 7075 8011 8090
Temper :
O H14 H24 H18 / T351 T3 T4 T651 T6 / H14 H24 H26 H16 / H32 H111 H321 H116 H112 / T6 T651 / T651 T6 T7451
H32: Strain-hardened and stabilized. The work-hardening rate is moderate, and the product has medium strength.
H34: Strain-hardened and stabilized. Similar to H32 but with higher strength.
H36: Strain-hardened and stabilized. Higher strength than both H32 and H34, but with reduced formability.
H38: Strain-hardened and stabilized. The highest strength in the 5052 series, but with the lowest formability.
O: Fully annealed, soft condition with the lowest strength. Excellent workability for deep drawing or spinning.
Thickness : 0.2mm-300mm
Width : 500mm-3000mm
Standard : GB/ 3880-2012 ASTMB209 EN485
Surface Treatment : Mill finish / Brush polish
PVC Coated : One side or two side PVC
MOQ : The inventory has no MOQ
Packing : Standard Export Packing
Port of Dispatch : It depends on the supplier's location and shipping arrangements
Delivery Time : The inventory is 5-7 days . 25-30 days for customized products
Payment : TT / LC / TT+LC
Alloy 5052 Composition: |
|
| Aluminum (Al): | 95.7%-97.7% |
| Magnesium (Mg): | 2.2%-2.8% |
| Iron (Fe): | 0.0%-0.25% |
| Copper (Cu): | 0.1% |
| Manganese (Mn): | 1.0%-1.5% |
| Zinc (Zn) | 0.1% |
| Chromium (Cr): | 0.15%-0.35% |
| Titanium (Ti): | 0.1% |
| Others: | 0.05% (each) 0.15% (total) |
